Welcome to Jiangmen Tufeng Chemical Co., Ltd.
TEL: +86-750-3988386
Oil based industrial paint
-
DB-1A Acrylic Metal Baking Paint Series
-
DB-2B Polyurethane Two-Component Paint Series
-
DB-3C Acrylic Plastic Paint Series
-
DB-4D Alkyd Antirust Paint Series
-
DB-7G Epoxy Anti-rust And Anti-corrosion Primer
-
DB-7G Epoxy Anti-Rust And Anti-Corrosion Paint Series
-
DB-7G High-temperature Anticorrosive Coating Is resistant To 300 Degrees
-
DB-8H Fluorocarbon Paint Series
-
DB-9K Rubber Paint Series
-
DB-11M High Temperature Paint Series
-
DB-12N Floor Paint Series
-
DB-16T Thermal Insulation Coating Series
-
DB-17 Polyurea Waterproof Coating Series
-
DB-18V Oil-Based Exterior Wall Paint Series
-
Polyamide Side Lacquer
-
Epoxy Cloud Iron Intermediate Paint
-
Epoxy Rich In Zinc Primer
-
Chlorinated Rubber Anti-corrosion Coating Material
-
Highly Chlorinated Polyethylene Anti-corrosion Coating
-
Water-resistant Coatings
Epoxy cloud iron intermediate paint
Epoxy cloud iron intermediate paint
I. Product Introduction:
The epoxy cloud iron intermediate paint is a two-component paint. It is mainly formulated from epoxy resin, mica iron oxide, anti-rust pigment, organic solvent, additives, etc.
Second, product features
Due to the superior properties of scaly mica iron oxide and epoxy resin, it has the following characteristics:
1) Good mechanical properties, toughness, collision resistance, impact resistance
2) Good adhesion and flexibility
3) Good anti-penetration shielding performance, sealing performance, water resistance, salt spray resistance, corrosion resistance, etc
III. Technical Parameters:
Check the results |
|||||
project |
Technical indicators |
Test results |
Measured |
Measurement method (national standard) |
|
Product color |
Conform to the template |
Symbols |
Gray-red |
Visual |
|
Varnish appearance (visual) |
Smooth and smooth without impurities |
Symbols |
Flat and smooth |
CB1721-79 |
|
luster |
Matte |
accord with |
28° (60° angle). |
GB1743-79 |
|
Solids content:% |
80 |
Symbols |
82 |
GB/T1725-2007 |
|
Fineness μm |
≤30 |
Symbols |
25 |
|
|
Hardness: h |
≥2 |
Symbols |
2 |
GB/T6739-2006 |
|
Drying time |
Table stem (min). |
≤20 |
Symbols |
1 |
GB/T1728-1989 |
Practical (h). |
≤24 |
Symbols |
24 |
GB/T1728-1989 |
|
Bending resistance (mm). |
2 |
Symbols |
2 |
GB/T1731-1993 |
|
Impact strength (cm). |
50 |
Symbols |
50 |
GB/T1732-93 |
|
Adhesion: (Grade) |
1 |
Symbols |
1 |
GB1720-79 |
|
Salt spray resistance: h |
≥ 500 hours |
Symbols |
No foaming, no rust, no shedding |
GB/T1771-2007
|
4. Scope of application
It can be used as the middle layer of high-performance anti-rust primer, such as epoxy iron red primer, epoxy zinc-rich primer, low surface treatment zinc-containing primer, inorganic zinc primer, etc., to protect the primer film and enhance the protective performance of the entire coating. It can also be used as a primer. Application areas
Coating of large steel structures, bridges, petrochemicals, power plants, concrete, engineering machinery, coastal facilities, drilling platforms and other fields. Generally, the general ordinary, industrial atmospheric environment, marine climate is more than 5 years, and the harsher corrosive environment needs to be considered.
5. Construction support
Diluent: special diluent for epoxy paint.
Front supporting coatings: epoxy iron red primer, epoxy zinc-rich primer, inorganic zinc silicate primer, low surface treatment zinc-containing primer, epoxy primer, inorganic zinc-rich primer , etc
Back-end supporting coatings: chlorinated rubber topcoat, epoxy topcoat, epoxy asphalt topcoat, alkyd topcoat, polyurethane topcoat, fluorocarbon topcoat, polysiloxane topcoat, etc
6. Coating temperature
Rain, fog, humid weather, temperature below 5 °C is not suitable for construction. When the temperature is lower than 5 °C, the epoxy resin reacts slowly with the curing agent, so it is not suitable for construction.
VII. Precautions
The paint should be thoroughly stirred before use, and must be used within 4 hours after mixing with the curing agent to avoid affecting the effect.
8. Storage and security protection
1. The product should be stored in a cool and ventilated place to prevent direct sunlight, and isolate the fire source and keep away from the heat source;
2. Operators should wear safety masks and gloves to avoid contact with skin or eyes, and wash with clean water if accidentally contacted.
CONTACT US
Add: Longan Industrial Zone, Duruan Town, Pengjiang District, Jiangmen City, Guangdong Province
Tel: +86-750-3988386
Mobile: +86-13822383835 (Ms. Wang)
Mobile: +86-13536058518 (Engineer Li Gong)
Email: sales@jmtufeng.com
FEEDBACK
Copyright © 2022 Jiangmen Tufeng Chemical Co., Ltd. 粤ICP备17115341号 SEO tags