Welcome to Jiangmen Tufeng Chemical Co., Ltd.
Oil based industrial paint
-
DB-1A Acrylic Metal Baking Paint Series
-
DB-2B Polyurethane Two-Component Paint Series
-
DB-3C Acrylic Plastic Paint Series
-
DB-4D Alkyd Antirust Paint Series
-
DB-7G Epoxy Anti-rust And Anti-corrosion Primer
-
DB-7G Epoxy Anti-Rust And Anti-Corrosion Paint Series
-
DB-7G High-temperature Anticorrosive Coating Is resistant To 300 Degrees
-
DB-8H Fluorocarbon Paint Series
-
DB-9K Rubber Paint Series
-
DB-11M High Temperature Paint Series
-
DB-12N Floor Paint Series
-
DB-16T Thermal Insulation Coating Series
-
DB-17 Polyurea Waterproof Coating Series
-
DB-18V Oil-Based Exterior Wall Paint Series
-
Polyamide Side Lacquer
-
Epoxy Cloud Iron Intermediate Paint
-
Epoxy Rich In Zinc Primer
-
Chlorinated Rubber Anti-corrosion Coating Material
-
Highly Chlorinated Polyethylene Anti-corrosion Coating
-
Water-resistant Coatings
DB-11M High Temperature Paint Series
DB-11M type is composed of silicone resin, special heat-resistant and anti-corrosion pigments, fillers, additives and other components, with excellent heat resistance, rust and corrosion resistance, and can withstand high temperatures above 800 ℃ (min 200 ℃ , 300 ℃, 600 ℃, 800 ℃ weather resistance), with 180 ℃ -220 ℃ / 30 minutes cross-linking curing, easy construction.
- Product Description
-
1. Introduction
DB-11M type is composed of silicone resin, special heat-resistant and anti-corrosion pigments, fillers, additives and other components, with excellent heat resistance, rust and corrosion resistance, and can withstand high temperatures above 800 ℃ (min 200 ℃ , 300 ℃, 600 ℃, 800 ℃ weather resistance), with 180 ℃ -220 ℃ / 30 minutes cross-linking curing, easy construction.
2. Scope of application
It is used for all kinds of high-temperature resistant equipment, pipes, chimneys, exhaust pipes, high-temperature hot gas furnaces, boilers, heating plates, etc., and all kinds of equipment that require high-temperature anti-corrosion on metal surfaces can be applied.
3. Coating properties and performance
Project
Index
Inspection standards
Appearance and color of paint film
Black, silver, medium gray, the paint film is smooth and the color conforms to the sample
GB9761
Viscosity (SC coating -4#/20℃)
60-90
GB/T1723
Adhesion (Cross-Hatch)
0
GB9286
Pencil hardness
≥2H
GB6739
Flexibility,mm
≤1
GB/T1731
Water resistance(40℃)240h
No significant changes
GB/T1733
Impact strength,kg,cm
≥35
GB/T1732
Heat resistance,600℃/30 min
No blistering, no peeling, slight discoloration
GB/T1735
Salt spray resistance,120h
≤2
GB/T1771
Weather resistance,200h
Loss rate ≤20%, pigment ▲E≤3.0NBS and the rest have no obvious change
ASTMG53
4. Construction reference
1. Before construction, the metal surface should be degreasing, derusting and dirt treatment to improve the adhesion of the coating film (preferably by sandblasting);
2. Construction ratio [5 kg of paint: 1 kg of curing agent: about 3 kg of thinner]
3. Xylene can be used as a diluent, preferably by air spraying, or brushing, but it is not easy to dry;
4. If precipitation is found during storage, it should be stirred evenly before use;
5. The gasoline resistance is poor, so attention should be paid to the construction.
5. Transportation and storage
1. The product should be waterproof and sun-proof during transportation to avoid collision, and should comply with the relevant regulations of the transportation department;
2. The product should be stored in a cool and ventilated place to prevent direct sunlight, and isolate the fire source, away from the heat source;
6. Safety protection
The construction site should have good ventilation equipment, and operators should wear protective equipment such as glasses and gloves to avoid skin contact and inhalation of paint.
Previous Page:
Next Page:
Related Products
Product Message
If you are interested in our products, please leave your email, and we will contact you as soon as possible, thank you!